I loaded up some 10's today

[The_Shadow]

Welcome aboard aussiebob.  Thanks for the data, is that MP5 is HK or clone?
Another fellow had some issues using the higher power loadings from his clone which had a lack some case support.  At the lower levels like what you listed he was OK.

I start some of my load testing at 1.260" but always work them back down the 1.250" for final loadings to function in all of my guns reliably...

Hope you enjoy the forum! 

[aussiebob]

It is a clone.

1.250" - 1.255" seems to feed into the pistol just fine.

I am getting another set of loads ready for accuracy and chrono testing.

Will post results.

I have a whole lot of once fired brass to load (approx 5000) . I am finally near the end of my last bulk buy loads.

The brass is a mix of headstamps. Starline, Winchester, others. Plus approx 2000 double tap nickel plated cases.

Anyone have a subsonic load for 165gr jacketed FMJFP bullet as I have some 125gr frangible bullets that I want to try when I get the suppressor for the MP5-10?

thanks

[REDLINE]

I am getting another set of loads ready for accuracy and chrono testing.

Will post results.

Can't wait.  Welcome to the forum!

[cwlongshot]

Last night I finished prepping three hundred more cases.

Cleaned, sized, necks flaired, primer pockets cleaned/uniformed, flash holes deburred, and fineally cases primed.

I'm thinking these will be mostly my cast 200 T/C bullet. With 50 more 200g XTP heavy loads.
I have been doing well with 231 and the Lyman 200g bullet I cast pretty hard.

The weather folks are for sating some bad weather for today thru sat AM. That means I will not be going home for a couple days so no loading for me till Sunday at the earliest.

CW

[The_Shadow]

Nothing like having stuff prepared ahead of time!     I always keep some empty but prepped brass to test new bullets or loads with. 

[REDLINE]

Nothing like having stuff prepared ahead of time!   

Amen!

[gandog56]

All types of powder go through my old Pact scale/dispenser!

[cwlongshot]

Loaded up an additional 150 tonight... 100 W/200g LEAD with 231 and 50 more W/Longshot and 200XTP loads...

Thats about 750 loaded... couple hundred more and ill be good for a while....

CW

[aussiebob]

Getting ready to do some loading
Some cleaned and primed once fired cases.

[attachment deleted by admin]

[aussiebob]

Getting ready to prime some more cleaned cases.

These plus the primed represent approx half of my 10mm cases.
Probably another bag of brass and three bags of nickel plated.



[attachment deleted by admin]

[REDLINE]

Nice!

[Caneman]

Loaded up an additional 150 tonight... 100 W/200g LEAD with 231 and 50 more W/Longshot and 200XTP loads...

Thats about 750 loaded... couple hundred more and ill be good for a while....

CW

what charge do you like with the cast 200gr?

i am gearing up to pour my own soon, so i am researching loads for cast boolits in the 10

[gandog56]

Getting ready to do some loading
Some cleaned and primed once fired cases.

I had just done 1000. Now I have a new box of 1000 Precision Bullets 185 grainers to do the last 1000 of my empty 10mm cases!

[cwlongshot]

Loaded up an additional 150 tonight... 100 W/200g LEAD with 231 and 50 more W/Longshot and 200XTP loads...

Thats about 750 loaded... couple hundred more and ill be good for a while....

CW

what charge do you like with the cast 200gr?

i am gearing up to pour my own soon, so i am researching loads for cast boolits in the 10

I don't like to list loads as I truly hate to hear some one was hurt taking my load verbatim... This load has proven safe in my Delta and my G20 with the KKM barrel...

Win LP primer, 6 grains of Win 231 powder, and my 200g cast Lyman bullets.

PLEASE check and work up to any loads as its unknown if these will be safe in other guns.

CW

[gandog56]

I'm out of town and can't remember the exact recipe I'm using right now. I know I've made them with Unique, HP-38, and I believe 2400.

In the old days I probably would have tried Blue Dot.