Stock III

will965 · April 30 2016 02:01:48 PM MDT

I know you said you shot some Buffalo Bore out of it so obviously with your wolf and your new Springs and guide rod it'll shoot the heavy stuff... Will it shoot the light crappy stuff like the FBI FBI light load or Armscor or any of the factory stuff? I'm seriously looking at this gun as my next 10 millimeter and the pictures you showed are absolutely beautiful!Should make one hell of a companion for my Glock M40.... ${$default_roll_eyes_smiley}$

01deuce · April 30 2016 02:27:54 PM MDT

I have shot the Buffalo bore 180gr HP, Sig 180gr fmj , Underwood 165 gr HP & 165gr fmj. The Sig would be the weakest of what I have shot, but it is definitely not a light load compared to some others. I assume it would be just fine with the lighter stuff. I will say it is very pleasant to shoot with the heavy loads.

will965 · April 30 2016 06:49:56 PM MDT

I'm reading and watching everything about these...Drooling over your pictures is just beautiful...For the same money I could get the new Sig but this has so much more I think then the sick bring to the table.

Intercooler · April 30 2016 06:54:58 PM MDT

Don't let the Cat out of the bag too much! ${$default_cool_smiley}$ These things suck ${$default_grin_smiley}$

will965 · May 01 2016 07:26:04 PM MDT

I've read much of your stuff intercooler!!! And yup, I agree, these are horrible....I would never.buy one! ${$default_tongue_smiley}$

01deuce · August 14 2016 06:59:12 AM MDT

Since I carry this iwb and intend to do the same with the limited. I decided to slim it down some to make it more carry friendly.
I slimmed down the ambi safety, installed a shorter standard mag release and re - profiled the rear sight some.
I also did the sight on the limited and will be sending a standard mag release and re profiled ambi safety off to be hard chromed.

Thanks to Intercooler for educating me on how to remove a Witness mag release.

Intercooler · August 14 2016 07:44:22 AM MDT

It looks really good! Good job!

Who do you have picked out for HC?

01deuce · August 14 2016 08:01:28 AM MDT

Quote from: Intercooler on August 14 2016 07:44:22 AM MDT
It looks really good! Good job!

Who do you have picked out for HC?

Thanks! Just bought a dremel yesterday, so it was my first go at something like this.

I have used Metaloy for a complete gun and for small parts before and have been very pleased. Chris has been a great guy to deal with and I plan to send these parts to him as well.

Intercooler · August 14 2016 08:43:12 AM MDT

I used Cogan for my Hunter and the finish exceeded factory greatly! Excellent work by that outfit!

sstewart · August 14 2016 08:48:04 AM MDT

Really really nice. What IWB holster did you use? I don't recognize the brand.

01deuce · August 14 2016 09:04:53 AM MDT

It's a company called Harvey's Holsters. They go to gun shows in Indiana and can make one for whatever you bring them. I had no luck finding anyone who has a mold to make one.

Intercooler · August 14 2016 09:10:49 AM MDT

It's interesting seeing some of the changes they made on the new models.

01deuce · August 14 2016 09:42:34 AM MDT

Quote from: Intercooler on August 14 2016 09:10:49 AM MDT
It's interesting seeing some of the changes they made on the new models.

As I stated about the new limited I bought, it doesn't have the LPA rear sight like on my stock III. In my opinion the LPA is a better sight then on my new limited.

01deuce · August 14 2016 09:44:50 AM MDT

Quote from: Intercooler on August 14 2016 08:43:12 AM MDT
I used Cogan for my Hunter and the finish exceeded factory greatly! Excellent work by that outfit!

I have used them in the past as well and I was very satisfied.

Intercooler · August 14 2016 09:46:44 AM MDT

Can you take a picture of the new sight? That's interesting! I'm hoping Henning will finish up his rear adjustable sight and end all the madness.