Glock 20/Lone Wolf

[GMAN]

Has anyone used one of these barrels? How does it work? Thanks

http://www.lonewolfdist.com/Detail.aspx?PROD=944&CAT=236

[Shane668]

GRAN I recently built a G20LS and used the 6.62" threaded barrel.  I'm still in the process of getting the recoil spring matched to my handloads but so far it has been very accurate and 100% reliable with factory ammo. I'll post a target pic as soon as I figure out how to post....hahaha

[The_Shadow]

I have three LWD barrels aa 9x25Dillon 6" for the G-20SF and two factory length in 357Sig and 9x25Dillon for my G-29.
The chambers have been great and performance even better.

Some day I will be looking to get a long 10mm barrel for G-20, if they had the 9" with threads cut, I'd probably buy one.
For now, I'm only using the factory 10mm barrel.

[ShadeTreeVTX]

I have the 2 port LW and the 6.62 threaded LW barrels for my G20sf gen3 and both have worked flawlessly and the 4.6 2port LW barrel on my G29sf gen3, which also works flawlessly. Some say you might need to polish the ramps but mine didn't need it.
I may have the distinction of having both of the Glock stock barrels and they are both virgins, never having a round fired through them.

Doug   

[Tenforme]

I have a 6" non-ported in 10mm and a 6" non-ported in .40S&W for my G20 SF.  I have had the both for over a year and have put ~ 1000 rounds through each, ranging from low energy PMC up to nuclear Underwood.  No problems with either.  Both are well made, accurate and give full case support (i.e. no evidence of case bulging).

I'm not sure if its my imagination but the 6" 10mm barrel seem quieter (from the shooters perspective) than the factory 4.6"

 

[Geeman]

I suppose I'm the only one with issues.

I tried one on a Gen4 G20 and it made it unreliable.  It wasn't because the round wouldn't go into the chamber.  It was because the slide would pass over top of the next round in the magazine with high impulse ammo.  It seemed it must have introduced just a bit more frame flex that pulled the magazine away from the slide at the worst time.

Stock barrel works great for everything but UW 220 cast, and that round just doesn't like to go into battery.  A more traditional failure to feed.

Greg

[ShadeTreeVTX]

If I'm not mistaken all of us with no problems have gen 3 10mm glocks.

Doug

[GMAN]

Yep, That's what I have, a G20sf, gen 3. Thanks for the info

[Chicho]

I have 3 different lone wolf barrels and all work great. Two are extended and ported and one is a conversion to 40sw. I do polish the feed ramps when I get them so I cannot speak to how they run straight out of the box.

[Shane668]

From an armours perspective I can tell you I'm not a fan of the Gen4 glocks.  They work great as long as you don't make any changes. The actual changes between the models were subtitle but for some reason you can't improve upon the trigger (I tried with a new G41) and they don't like aftermarket barrels? Any one wanting to customize a Glock I will always recommend a Gen3, and for the time being Glock is still producing them.

[redbaron007]

From an armours perspective I can tell you I'm not a fan of the Gen4 glocks.  They work great as long as you don't make any changes. The actual changes between the models were subtitle but for some reason you can't improve upon the trigger (I tried with a new G41) and they don't like aftermarket barrels? Any one wanting to customize a Glock I will always recommend a Gen3, and for the time being Glock is still producing them.

My G20 G4 has worked flawlessly with the KKM 6" barrel.

[Bigbehr]

no issues with my stock length lone wolf, or storm lake. Both are accurate and have had 0 malfunctions.

[N1vraM]

From an armours perspective I can tell you I'm not a fan of the Gen4 glocks.  They work great as long as you don't make any changes. The actual changes between the models were subtitle but for some reason you can't improve upon the trigger (I tried with a new G41) and they don't like aftermarket barrels? Any one wanting to customize a Glock I will always recommend a Gen3, and for the time being Glock is still producing them.

Are you referring to drop in trigger kits not working?

[Big Shrek]

G20SF with a 9" Lone Wolf barrel...thinking about getting the end threaded for a compensator
Perfect Whitetail Deer & Hog hunting pistol now!!

[JamesL73]

I have a G20 gen 3 SF, have never tried anything other than the stock 4.6" barrel. I am wondering how much difference does the 6" make? Pros and Cons of switching to a 6"??