Quote from: Texashogman on October 02 2017 09:25:04 AM MDT
after Las Vegas this morning/last night--- I don't see any positive process with taking suppressors off the NFA list---I can see even more scrutiny and regulations coming down the pipe if anything with NFA items

Agreed. Not gonna happen now.

It looks like we may get suppressors soon without the $200 tax and year wait. I am researching 10mm suppressors so I can try to beat the rush.
I have both a P220 and a 10mm AR15. I am looking at both 45 & 40 caliber cans.
Any recommendations? I would love to hear from personal experience but if there is a make/model that is considered to be the best any information is appreciated.
Thanks.

I got a Trijicon RMR. Cabela's had them for $260 shipped a few weeks ago.
I got the 3.25 AND the 6.5
Who does good mill work? I'm looking at Suarez international.

Quote from: Liver on September 09 2017 03:32:02 PM MDT
I've been reading and searching on the Sig 220 10mm.   Aside from the obvious da/sa vs SAO, all the internals are exactly the same.  All have srt trigger. 

They all have the same barrel. 

They are stainless steel with different finishes. 

Basically get whatever controls you want, and the finish you want. 

I'm looking at this gun to MILL a red dot on.   I've had a 226 for years that I've milled for an RMR.

Who milled your slide? I am looking at Suarez Into to do mine. Thanks.

I got this on GB. Never did find the adjustable rear sight. Gonna have this milled for my RMR.

Quote from: Pablo on August 30 2017 07:01:03 PM MDT
I shoot HAP bullets out of my RMW 10mm all the time - 11" barrel. Some are over book (don't tell anyone)

1) They are very accurate.
2) They are damned destructive
3) I wish we had pigs to shoot, and I can dream - but my guess is they will be great.

I am torn between the XTP and the HAP.  The sensible side of me says to spend a few extra cents per bullet and get the XTP. The cheap side of me says get the HAP. We shoot them with 22 mag all the time with no problem. Any 10mm will do fine.

How does your RMW run? Is it picky about ammo? Did you have to tweak it to dial it in?

I reload too and will be running over book as well. [emoji44]

Can I buy the Federal JSP bullet anywhere? I see they offer it as loaded ammo but I can't find the bullets anywhere.

https://www.midwayusa.com/product/1001296875/federal-premium-vital-shok-ammunition-10mm-auto-180-grain-trophy-bonded-jacketed-soft-point-box-of-20

8" barrel.

How about a JSP 38-40 bullet? Anybody using those?

I have an AR being built by RMW extreme. Should be here next week.

These are hand loads so I can make them as hot as needed. Or do you mean energy transfer?

Hornady makes a 200 grain hollow point that they say is for action shooting.  If you read the description it says they are the XTP without the cuts in the jacket to aid in expansion.

I would use them for hogs. Any opinions on these?

What I really want is the XTP Flat Point.  They are just like the HP but with a smaller opening. Most people don't know they exist.  I have them for my 357 carbine but have not been able to find them for 10mm.

https://www.midwayusa.com/product/1165110709/hornady-action-pistol-hap-bullets-40-s-and-w-10mm-auto-400-diameter-200-grain-jacketed-hollow-point

Quote from: Mike D on August 14 2017 11:52:47 AM MDT
Ron at RMW Extreme is your man for the upper.

The QC10 lower assembles like any other lower.




Sent from my iPhone using Tapatalk Pro

Is it picky about ammo?

I got the QC10 lower and the Glock mags. I have Ron Williams working on the 8" upper right now, and I have a Bravo Company LPK and Shockwave "arm brace" on order.

Almost there!

I am in contact with Ron from RMW extreme. I think I'll have him build and tune an upper for me.