Hey guys, I hope that since this is the "reloading" section, that it is appropriate to post this question here.
Do you guys use a powder trickler when working up "maximum" loads? If so, what brand? If not, what other method/device do you use? Do tricklers work well with large (i.e. 800-x) and small (i.e. AA#9) grain powders?
I've been trying out a few more "rudimentary" tools, such as white office paper, etc. There has got to be a better way! I've looked at a few different options out there, such as the Lyman, Redding, and RCBS.
Thanks!
I use the small RCBS trickler (hand op) set next to the scale pan, transfer a pan of powder thrown from the RCBS Uniflow then set it on the RCBS 5-10 beam scale, the kernel up if necessary.
With Blue Dot, LongShot or 800X; 0 to 5 flakes/kernnels to level up when the powder hopper is set and at least a 1/3 full
Working with H-110 and 296 today, a tap or two to sprinkle a little and it would level up
Power Pistol on the money unless the hopper gets low
Hornady Lock N Load digital powder dispenser.
I use the same set up as the Shadow.....RCBS trickler works well with any powders I've tried, even 800-X. If trying for consistency I just set the powder measure to throw just under the amount wanted then use the trickler into the pan while weighing. Nothing complex about the design of the trickler so I'd think most any brand would work the same. Also found the RCBS powder measure to meter 800-X reasonably well, nothing like I've read others complain of.
I use the RCBS digital trickler with the scale. I have never used 800x but anything that is stubborn I use the RCBS 5-10 beam scale.
I have all three and like the Redding best. It's heavier with a smaller foot print. So its better suited for my scale stand.
But the RCBS was used allot as wel a Lyman before that all work well.
CW
Lyman, it works fine with 800x
Thanks for all your opinions!
Those electric powder dispenser/scale combos look pretty nifty, but are far past my budge and space requirements for the time being.
I'll let you all know what I end up with and how I like it.
I have a Lyman electronic powder measure/scale and it works great but slow. I bought it off a friend who was using it to load 223 blasting ammo for an AR and it was too slow for him. I use a powder measure for that stuff and weigh every 10 or 20 rounds.
What they are made for is rifle cartridges utilizing stick powders. Works fine for 6.5X284 and the various magnums I shoot. It take about 30 seconds to get a charged weighed but they are always right on the nuts. I do not shoot that many of those calibers at one range sesion anyway. Great for weighing different weights for load development and sneaking up on max.
Good luck.
I use a set of plastic measuring spoons and trickle powder from the 1 tsp spoon. They were really cheap, and after a little practice, are every bit as accurate. I can drop one-two granules of powder at a time.
Quote from: sqlbullet on March 22 2013 07:48:29 AM MDT
I use a set of plastic measuring spoons and trickle powder from the 1 tsp spoon. They were really cheap, and after a little practice, are every bit as accurate. I can drop one-two granules of powder at a time.
Goodness brother, If momma reads this your gonna be in a world of bad... :o I happen to have a couple RCBS tricklers, PM me your addy and I'll get one off to you. Now quick like, get them spoons washed and back in the drawer!! :o :o :o
CW
Ah...But I am the family cook, and these were rejects from my kitchen. I like stainless steel for my measuring spoons.
Thanks for the concern though. Always good to stay outta momma bears way ;D
I like the old Hornady manual powder trickler myself.
Ended up buying an RCBS 2 trickler on sale. I will update my post after I get some more experience with it this summer.