Those of you with the EAA guns may find this of interest... ;)
(https://coppergungrips.com/images/92830adf76ea7ce07491a9d4806d7bd3_7k5s.jpg)
https://coppergungrips.com/ (https://coppergungrips.com/)
More info from an actual user and his experience with the grips on his EAA...
http://www.roguechristian.com/brenten_forum/viewtopic.php?f=20&p=3536#p3536 (http://www.roguechristian.com/brenten_forum/viewtopic.php?f=20&p=3536#p3536)
I guess you have to be registered to view it.
Maybe so...Oh well! :-[
The Xtreme panels are nice, but I don't care for logos. If Henning does another run of his I may have to bust open the wallet ???
I like the Copper Grips. Do you guys know if the Witness grips would fit my Stock 1?
They should.
Thanks Intercooler! I also like the Extreme grips, but for the price I'll probably get the Copper.
I gotta find out if they'll send-out a small sample of the surface
They should fit the Stock 1. I inquired about fitting on Stock 2 and it's a go.
I know that they wont fit a Hunter. I got a set of Green, but I didn't return them, because I plan on buying a Match.
On a Match nothing beat a Hogue wrap-around and it looks awesome!
(https://scontent-a-iad.xx.fbcdn.net/hphotos-ash2/t1/425410_341570575880981_814883523_n.jpg)
Looks great IC
I love the Hogue WAR FG Grips too
I have them on my CZs and Ruger MkII Target, but when it comes to the Witness Large (DA / SA) Frame, they just seem too large for my small hands
Now a Single Action may be fine, even for me
But really IC, you gotta loose the Slotted Screws 8)
Check this guy out:
http://czscrews.angelfire.com/
Here's my three with his Torx Head Screws:
(http://i1108.photobucket.com/albums/h414/denstinettm14/TheTrio-1.jpg)
(http://i1108.photobucket.com/albums/h414/denstinettm14/TorxScrews.jpg)
They fit the Tang's fine?
The one he sent me fit right out of the Bag
Do the Hogue wrap-around grips fit the EAA full size steel 10mm ? (mod. # 999200)
Do you have a link?
Quote from: Tomcat 10 on February 15 2014 06:40:45 AM MST
Do the Hogue wrap-around grips fit the EAA full size steel 10mm ? (mod. # 999200)
Yes, with a bit of work, they will fit
You need to sand the Backing Plates a bit, because they intrude on the Mag Well and hang-up the Magazines
They need to be Strrreettched to fit, left to right, a little heat will help here
And, in some cases, the Screw Hole needs to be Keyed a bit toward the edge
But yes, they do fit
Has anyone tried a set of Hogue G10's on a large frame Witness? Hogue only lists grips for the small frames.
http://www.hoguestore.com/index.php?main_page=product_info&cPath=116_125_553&products_id=7542
I ordered the Hogue Wrap-Around , this morning . I hope I will be able to make them fit EAA 999200 .
Before you even try to put it on you will need to remove some material on the locking pads (plastic). The best way to figure that out is position it in place looking at each side with the opposite side peeled back for viewing. When you get it down to where it is flush with the metal of the mag channel give it a little more clearance (maybe .010"). Don't go too far though as it might not have enough meat to hold in position correctly. Try putting a full magazine in it after you get it on and see if they slide out easily. If not, take a bit more off.